Posts Tagged ‘Southern Highlands’

« Older Entries

Faucet Aerators for Las Vegas Plumbing?

Monday, April 30th, 2012

A tap aerator or faucet aerator is a device which is added to the tip of water faucets, and are best used inside with bathroom sink faucets and kitchen plumbing for Las Vegas homes.  They are used to separate water streams into a number of smaller streams, in essence adding air to the water stream.  This reduces the amount of water which comes out of the tap at one time while also reducing the amount of backsplash which occurs when the faucet is turned on.

Utilizing faucet aerators can be one of the most inexpensive ways to save money on water consumption and save energy.

There are two main types of faucet aerators, some which use metal or plastic screens to separate the water, and some which do not use screens. One advantage to those without screens is that they eliminate problematic clogging which occurs on screen aerators due to sediment buildup.  There are also aerators with off-valves and swivel aerators which allow users to direct flow to wherever the water spray is needed.

There are three main flow-types seen today. The needle method creates a circular pattern of small, single streams of water with no water-flow in the very center.  The aerated method created a tubular flow with air mixed into the water, creating a single stream of bubbly water.  The laminar method has no air mixed in which makes for a single stream of water with no bubbles.

Many aerators are designed as more economical low-flow aerators which optimize the water flow while still providing optimal water-flow performance.  In kitchens these low-flow options decrease flow from 2.2 gallons per minute to 1.5 gpm or 1.0 gpm, saving anywhere from 32% to 54% of water-usage.  For Faucets found in bathroom plumbing, the water-flow is decreased from 2.2 gpm to 1.0 gpm or even 0.5 gpm saving from 77% to 84% of water usage.  When engineered properly, low-flow or economic aerators can provide increased perceived water pressure while in actuality helping to save water.

When purchasing new faucet aerators, ensure that you find the proper type (male or female) and the proper size (regular or small).  There are dual-thread options for those who do not know whether a male or female aerator is necessary.  Also, look at the tap aerator’s price in conjunction with how much savings it can provide in water usage annually and see how little must be spent on each faucet in order to save hundreds of dollars.

For more assistance with choosing the correct faucet Aerator please call Yes! Plumbing.

Tags: , ,
Posted in Bathroom Plumbing, Kitchen Plumbing for Las Vegas, Plumbing | Comments Off

Repairing Common Sump Pump Problems: A Troubleshooting Guide from Southern Highlands

Monday, April 9th, 2012

Sump pumps in Southern Highlands, and almost everywhere else, is a very crucial aspect of a home’s plumbing because it removes excess groundwater.  When a home gets too much ground  water you home could flood, but sump pumps prevent this from happening.  If you have ever had water damage in Southern Highlands or anywhere else, you will understand why sump pumps are vital. If a pump comes to a halt or is unable to turn off, residents can typically fix this problem themselves. During months of increased down pour and flooding is almost inevitable, that is why it is a good idea to examine a sump pump on a very frequent basis to ensure it’s operating properly.

You can maintain your pump by having it inspected by a professional plumber, and keeping the pump clean and the well free of debris. Feel free to call Yes! Air Conditioning & Plumbing if you have questions about how to maintain a sump pump, or to make an appointment for an annual inspection and professional cleaning.

Most issues can be repaired easily and without much plumbing maintenance from a professional. Here’s a troubleshooting guide to help you solve minor issues with your pump.

Check for Electrical Problems

Always check to make sure the sump pump is fully plugged in and that there aren’t any fuses that have burned out. If there is standing water in the basement, you should take extra precautions when handling any electrical equipment, even a plug. Call a plumber or electrician for advice if you have any safety concerns.

Check the Float Switch

Just like the float in a toilet tank, the float attached to the side of your sump pump acts as a guide for turning the pump on and off. This is called the float switch, and it usually has a large bulb or other floatation device attached to a metal arm. This float detects the water level inside the well, and it turns the pump on when the water reaches a certain height in the well.

If the pump is plugged in and there are no blown circuits, move the float switch up and down to see if it will turn the pump on. Debris can get trapped underneath the float causing it to stick. If the motor is constantly running, this switch may be stuck in the “on” position if debris is lodged underneath it, or if there’s substantial corrosion.

You can actually move the entire pump around to change the position if there’s no apparent debris causing the issue. Sometimes the pump gets shifted around slightly, and the float switch cannot work properly if the pump isn’t plumb or level. Be careful not to move it too much, since it could damage the drain line attached to the pump motor.

If your motor is constantly running, and none of these steps work, the motor could overheat and stop working. Unplug the pump while you’re investigating the problem, and if none of these steps work, call a professional plumber.

Check for Clogged Filters

In addition to causing issues with the float switch, debris trapped in the screen can also cause the motor to overheat or shut down. If your filter is dirty, try to get out as much of the debris as possible, but if this doesn’t solve the issue, you could have a clogged drain line. In this case, you will need to call a professional plumber to snake out the line.

Preventative Maintenance Tips

You can prevent issues with the sump pump in your Southern Highlands home with a few preventative maintenance tasks. Keep debris from falling into the well as much as possible, and clean out any particles that could clog the screen or affect the operation of the float switch. Occasionally inspect the pump and well for any corrosion or other concerns. If you are comfortable with the operation of your pump, drain and clean the entire well and pump at least once a year.

Lastly, call a qualified technician at Yes! Air Conditioning & Plumbing for a yearly sump pump maintenance visit.

Tags: , ,
Posted in Plumbing, Plumbing Maintenance, Sump Pumps in Southern Highlands | Comments Off

The Root of the Problem – Why Some Sewer Lines Get Blocked in Las Vegas?

Tuesday, March 27th, 2012

Have you ever had to fix a blocked sewer line?  Well if you have, you are familiar with the nightmare that Las Vegas drain and sewer maintenance can be.  Sewer lines are comprised of incredibly tough components for a purpose: mostly because we collectively want to keep their contents inside. So, when a sewer line gets blocked and starts backing up or seeping — or even cracks under the stress — it can be a real mess.

If you have never had encountered a sewer line block, count yourself lucky.

Whichever category you fall into, it is important to know about causes of sewer blocks lie, so that you have an idea what you are up against should you ever encounter (another) one, as well as being able to take some reasonable prevention measures. Read on to learn about some of the common culprits that block up sewer lines.

Flushed Objects

The most preventable common cause of a blocked sewer line is the flushing of objects that should not be flushed. Sewer lines are not meant to handle solid objects like diapers, sanitary napkins or other garbage, so if these get flushed down the toilet — either intentionally or by accident — it can cause an ugly block.

Even smaller objects or bits of debris that seem to move fine through the sewer line can build up over time to cause a block. Paper towels, hair, grease or dirt can collect on the walls of the line and cause a block as well.

Tree Roots

It may seem like nothing happens beneath the ground of our lawns, where the sewer line runs. In fact, there is quite a bit of life going about its business under there, including the root systems of the trees in your yard. These roots can grow right into your sewer line, infiltrating it and causing a blockage.

Defect

The last main cause of a sewer link blockage is shoddy materials. Although sewer lines are meant to be made of high quality material because of the stress they perform under, it is still possible for one to collapse or bulge with use.

If Repairing a blocked sewer line is what you need to do, it’s best to call Yes! Plumbing for assistance. To avoid having to make that call, the best thing you can do as a homeowner is keep solid objects from being flushed down into the sewer line. It can save you a huge headache later on.

Tags: , ,
Posted in drain and sewer maintenance, Plumbing, Repairing a Blocked Sewer Line | Comments Off

Why is the Garbage Disposal in My Las Vegas Home “Humming”?

Wednesday, March 7th, 2012

Ah, the garbage disposal: one of the greatest conveniences and frustrations of a Las Vegas kitchen. When it is working well, it seems like few things could be better than this magic machine that whisks away our gross garbage. But when it is on the fritz, there is nothing more annoying.

One common occurrence is the “humming” garbage disposal. You flip the switch to turn the disposal on, but instead of spinning up and sucking those coffee grounds away, it just makes a humming noise and doesn’t do anything. Definitely frustrating. The good news is that since it is making that humming noise, you may be in OK shape. Read on further kitchen plumbing tips.

There are two basic causes of the humming phenomenon. Let’s discuss the simpler one first.

Stuck Flywheel

Most of the time, the problem is as simple as a stuck flywheel. Usually this problem is identified by the brevity of the humming sound, as the garbage disposal will either reset itself or the circuit breaker will trip and the whole thing will shut down.

To fix a stuck flywheel, follow these steps:

  1. Shut down the power to the garbage disposal by shutting of the circuit breaker or pulling the fuse.
  2. Using an offset wrench (it came with the disposal unit, but you can buy a replacement at the hardware store), turn the flywheel clockwise to dislodge it.
  3. For a no-wrench fix, stick a wooden broom handle down the drain and into the disposal, then use that to manually turn the blades.

If the problem is just a stuck flywheel, that should take care of it. However, there is another, more sinister explanation for the humming sound.

Seized Motor Bearing

If your efforts to free the flywheel did not get the disposal working again, then you may have a seized motor bearing on your hands. A disposal with a seized motor bearing needs to be replaced. It’s as simple as that.

However, before you go ahead and assume the worst, it would not hurt to have a professional look at it. It is possible that the flywheel is just quite stuck and needs the touch of a pro. If not, call Yes! Air Conditioning & Plumbing, and we can go ahead and install a new unit for you.

Tags: , ,
Posted in Garbage Disposal, Kitchen Plumbing, Plumbing | Comments Off

What Spring Valley Residents Need to Know About Point of Use Water Heaters

Tuesday, February 28th, 2012

For years, most Spring Valley residents have used the same system to heat their water. A single tank that heats and stores water at a set temperature for whenever it is needed. That system, as well as it works, is not very efficient, and with costs for gas and oil rising so much in recent years, many people are looking for better ways to heat their water.

That’s where point of use water heating comes in. These tankless water heaters are designed to heat your water when you need it heated instead of filling a tank of 50 or 60 gallons and heating it continuously even when you don’t.

How Point of Use Water Heaters Work

A point of use water heater works by directly heating the water supply to a single fixture. So, you would install a point of use water heater on your kitchen sink and only one water supply pipe would go to that heater. When you turn on the hot water faucet, the point of use heater would turn on (using electricity) and heat your water to 170 degrees F.

These devices only work on a single fixture at a time but they are much less expensive to purchase than a whole house tankless hot water system. Additionally, you can control where hot water is available.

The Advantages of Point of Use Hot Water

A tank hot water system can cost hundreds of dollars of year extra to run, especially if your family doesn’t use much hot water. Imagine what happens if you have four children that go off to college. Your “just big enough” tank suddenly becomes way too big and your bill stays unnecessarily high.

Point of use heaters allow you to decide where hot water is available and have instantly available hot water as you need it. The cost of the units and installation is affordable for most homeowners and you don’t have to commit to a whole house system if you are not ready.  If you have any questions about this topic please call Yes! Air Conditioning & Plumbing

Tags: , ,
Posted in Kitchen Plumbing, Plumbing, Water Heater | Comments Off

What Causes Discolored Water for North Las Vegas Residents?

Monday, February 20th, 2012

Water discoloration can be troubling, because it makes it seem like your water is unclean. While sometimes discolored water can be cause for concern, other times it has pretty mundane origins, and will only require minor plumbing maintenance.

Check out these common causes of discolored water:

  • Yellow/brown/reddish water is usually caused by rust, either in the water mains that run from the waiter supply or the pipes in your home. If the water is only discolored momentarily when you first turn the water on, it is probably rust in your pipes that gets flushed out quickly. If it persists longer, it may be rust that was stirred up in the water mains. Turn a few of your cold taps on for several minutes, or just turn the tap off and wait about thirty minutes.
  • Water that appears white or cloudy often does so because of trapped air bubbles. Air that is under pressure in your pipes gets released when you turn the tap on, which causes tiny bubbles, just like in a bottle of soda. This has no effect on your water’s quality. The discoloration should dissipate after standing for a few minutes.
  • Sometimes water appears to have a greenish hue, especially when standing under fluorescent light. This is sometimes due to tiny copper traces from the piping in your home, or — depending on the climate — seasonal algae blooms in the local water supply. Either way, this green color is usually harmless.
  • Blue water can occur for a few reasons. One is severe copper corrosion in the plumbing system, which leeches into the pipes. A second cause can be toilet cleaner. If you use a cleaning product in your toilet tank, sometimes that can cause your tap water to turn blue. If you suspect this is the case, do not drink that water and immediately call a local professional to administer a water test. The chemicals in such cleaners can be toxic and hazardous to your health.

Keep in mind that those are some of the most common causes of discolored water. There can be others, and if you are unsure, you should call Yes! Plumbing for assistance.

Tags: , ,
Posted in Plumbing, Plumbing Advice, Plumbing Maintenance | Comments Off

Henderson Plumbing Tips: How and Why to Recaulk Plumbing Fixtures

Monday, February 13th, 2012

In Henderson you probably don’t pay much attention to the caulking, or plumbing maintenance around your tub and sinks. It is one of those things that is always there, working kind of behind the scenes, that you never seem to notice until something goes wrong.

The thing about caulking, though, is that something can go wrong with it rather quickly. Because of the high frequency of use of tubs and sinks, the caulk that seals the space between the fixture and the wall can deteriorate and crack over time. This can cause gaps in the caulk or cause the fixture to come loose from the wall, which would necessitate more bathroom plumbing.

When this cracking and erosion happens, water from your bath, shower head or faucet can seep in between the fixture and the wall, potentially causing water damage and fostering colonies of mildew and mold.

Cracked caulk is inevitable with daily use, so you don’t need to worry about preventing it. Instead, learn how to properly fix the situation with a fresh caulk job:

  1. Scrape away all the old caulk from around the fixture using a utility knife or putty knife. Take care to remove all the old caulk while also avoiding scratching porcelain fixtures.
  1. With all the caulk gone, clean out the joint thoroughly. This will remove any last traces of caulk, as well as any other dirt or buildup. If you notice mildew or mold, use a chlorine bleach solution to clean the joint before recaulking.
  1. Once the joint is dry, recaulk it using a bead of caulk that is just slightly wider than the joint. This ensures an adequate seal. Wipe any excess away with a rag.
  1. Allow the caulk to dry thoroughly before using the sink or tub. Read the instructions on the caulk for an estimated drying time.

Take note that it is very important to thoroughly remove all the old caulk and clean everywhere along the fixture joint before applying the new caulk. Otherwise, the new caulk will not adhere properly and potentially damaging dirt may get sealed into the joint.

If you followed all the steps carefully, you should have a fresh seal of caulk that will last you another several years!  If you would rather have a professional handle this delicate situation please call Yes! Plumbing.

Tags: , ,
Posted in Bathroom Plumbing, Plumbing, Plumbing Maintenance | Comments Off

Blue Diamond Plumber’s Tip: Common Toilet Problems

Monday, February 6th, 2012

The toilet is one of our most important parts of your Blue Diamond home’s plumbing. But it also prone to its fair share of problems. Let’s take a look at some common toilet problems and how to fix them.

  1. Running
    Perhaps the most common of toilet annoyances is the constantly running toilet. Not only is the sound irritating, but it can result in high water bills.  Fortunately, it is simple to diagnose and fix. Just look into the tank at the flapper. If it is not seated properly, adjust the chain to give more slack. If that doesn’t solve the problem, the flapper may be worn and need to be replaced.
  1. Slow draining bowl
    Also known as a weak flush, this one is also fairly easy to fix. A weak flush is usually caused by clogged flush holes, which are underneath the rim of the bowl. Clearing the clogs should fix the problem.
  1. Phantom flush
    Although it won’t actually flush, sometimes you may hear the tank spontaneously start to refill as though someone has just flushed. This just means the water is leaking out of the tank, which can usually be fixed with a new flapper, as with problem #1.
  1. Suction sounds
    If you flush the toilet and hear sucking or gurgling sounds emanating from the tub or sink, that usually indicates a clogged vent pipe. Such clogs usually originate in the roof, such as a dead bird falling into vent pipe up there. You may be best served by calling a plumber to fix this one, in order to avoid making the problem larger.
  1. Clogged or overflowing
    Lastly, of course, is the clogged or overflowing toilet. While wearing gloves and holding your nose, use a plunger or pipe snake to clear the drain. If that doesn’t get it done, the clog may be too large to handle without professional equipment, so you had better call a plumber.

If you have a problem with your Blue Diamond home’s plumbing, remember that Yes! Air Conditioning & Plumbing offers 24/7 emergency service!

Tags: , , ,
Posted in drain and sewer maintenance, Plumbing, Plumbing Maintenance | Comments Off

Blue Diamond Water Line Tips: Why Water Line Replacement and Repair is Not a Do-it-Yourself Job

Wednesday, February 1st, 2012

Even if you are comfortable doing some of the minor plumbing repairs in your Blue Diamond home, you should never attempt to replace a main water line on your own. You could potentially hit an underground utility line and do major damage, not only to your home, but the homes around you as well.

Only a qualified plumber has the experience and required tools to replace the broken line and affected pipes. Additionally, the sooner you call a qualified plumber to repair or replace your main water line, the less potential there will be for further damage to your home. If you aren’t sure whether or not you need repair work on your water line, there are some definite signs to look out for.

Water backing up in your yard is one of the most obvious indications of a main water line break or leak, but you could also notice drops in water pressure or high water bills before this happens. If you notice any of these issues, it’s best to call a plumber before it turns into a major hassle and expense.

While extreme weather can cause a water line to break, it’s typically caused by corrosion or root penetration. This is another important reason to have your pipes and plumbing system inspected once a year by a qualified plumber. Video scans of your pipes can detect any issues before they get worse.

Plumbers are also able to repair and replace the water line in your TOWN NAME home with advanced technology that does not require digging up your yard. Call COMPANY NAME if you notice any obvious problems or suspect a leak in your main water line. Replacing a water line should be handled by a professional, and we have the experience, skills, and proper equipment required to get the job done safely and efficiently.

Tags: , ,
Posted in Plumbing Advice, plumbing repairs, water line | Comments Off

MacDonald Ranch Plumbing Tip: How to Replace a Toilet Seal

Monday, January 9th, 2012

If you have ever taken a look at the base of your MacDonald Ranch home’s toilet where it meets the floor, you may have noticed a bead of caulk sealing the base of the toilet to the floor. While this watertight seal is important, there is actually a more important seal hidden within the base of the toilet.

Inside, your toilet sits on a wax ring that serves to keep sewer odors from wafting into the room, seal water from leaking from the bathroom plumbing and provides a degree of stability to the toilet installation. You may need to replace that seal if:

  • You notice leaking water at the base of the toilet.
  • You smell sewer odors in your bathroom.
  • The toilet is unstable or rocks side to side at all.
  • The toilet was removed temporarily for any reason, such as replacing it or putting down new flooring.

As it happens, replacing the toilet seal is a fairly simple and inexpensive operation that you can do on your own. To take care of this job yourself, follow these 16 steps:

  1. Shut off the water supply.
  2. Empty the bowl and tank by flushing the toilet. You may have to flush twice.
  3. Get the bowl and tank completely dry by soaking up any remaining water with a sponge, rag or towel.
  4. Remove the bolts that attach the base of the toilet to the floor.
  5. Disconnect the supply line the leads into the toilet.
  6. Gripping the bowl, rock the toilet gently back and forth to break the seals.
  7. Lift the toilet free from the floor.
  8. Now you can see the remnants of the old wax ring. Remove all that thoroughly.
  9. Place the new seal in place of the old one, centering it exactly, with the rounded side up.
  10. Replace the toilet over the seal and flange.
  11. Have a seat! No, really; this helps to create a new seal between the ring and the toilet.
  12. Reattach the nuts you removed from the base.
  13. Reconnect the water line.
  14. Turn the water supply back on.
  15. Flush the toilet, looking carefully for any leaks.
  16. Apply a new bead of caulk to the bottom of the bowl to complete the sealing job.

And if you run into any problems, talk to your MacDonald Ranch plumber.

Tags: , , , , ,
Posted in Plumbing | Comments Off

« Older Entries