Posts Tagged ‘Henderson’

« Older Entries

Henderson Plumbing Tips: How and Why to Recaulk Plumbing Fixtures

Monday, February 13th, 2012

In Henderson you probably don’t pay much attention to the caulking, or plumbing maintenance around your tub and sinks. It is one of those things that is always there, working kind of behind the scenes, that you never seem to notice until something goes wrong.

The thing about caulking, though, is that something can go wrong with it rather quickly. Because of the high frequency of use of tubs and sinks, the caulk that seals the space between the fixture and the wall can deteriorate and crack over time. This can cause gaps in the caulk or cause the fixture to come loose from the wall, which would necessitate more bathroom plumbing.

When this cracking and erosion happens, water from your bath, shower head or faucet can seep in between the fixture and the wall, potentially causing water damage and fostering colonies of mildew and mold.

Cracked caulk is inevitable with daily use, so you don’t need to worry about preventing it. Instead, learn how to properly fix the situation with a fresh caulk job:

  1. Scrape away all the old caulk from around the fixture using a utility knife or putty knife. Take care to remove all the old caulk while also avoiding scratching porcelain fixtures.
  1. With all the caulk gone, clean out the joint thoroughly. This will remove any last traces of caulk, as well as any other dirt or buildup. If you notice mildew or mold, use a chlorine bleach solution to clean the joint before recaulking.
  1. Once the joint is dry, recaulk it using a bead of caulk that is just slightly wider than the joint. This ensures an adequate seal. Wipe any excess away with a rag.
  1. Allow the caulk to dry thoroughly before using the sink or tub. Read the instructions on the caulk for an estimated drying time.

Take note that it is very important to thoroughly remove all the old caulk and clean everywhere along the fixture joint before applying the new caulk. Otherwise, the new caulk will not adhere properly and potentially damaging dirt may get sealed into the joint.

If you followed all the steps carefully, you should have a fresh seal of caulk that will last you another several years!  If you would rather have a professional handle this delicate situation please call Yes! Plumbing.

Tags: , ,
Posted in Bathroom Plumbing, Plumbing, Plumbing Maintenance | Comments Off

Kitchen Plumbing Advice from Top Sun City Summerlin Plumbers

Wednesday, January 25th, 2012

Considering how often we use our kitchen sink – i.e., many times per day, every day – and all the grimy business that it usually has to put up with, it’s kind of amazing that we don’t all experience headaches with our kitchen plumbing once a week. Chalk that up to the marvels of modern engineering and design.

That does not mean that kitchen plumbing is perfect, though, and all Sun City Summerlin homeowners face problems with their kitchen plumbing from time to time. Fortunately, many such problems are fairly common and routine and therefore are easily remedied.

Below are 3 common kitchen plumbing problems and some possible solutions for each:

  1. Clogged drain
    Probably the most commonly aggravating of all kitchen sink problems is the clogged drain. If you have never had to deal with one, first thank your lucky stars and then brace for impact, because you’ll probably have to soon. This is usually caused by some piece of food or other deposit obstructing the sink. Try plunging it out, or breaking it up by pouring boiling water or white vinegar down the drain. This may take several attempts. If none of that works, you can resort to a commercial drain opening product.
  2. Leaky faucet
    Got a dripping sound keeping you up at night? Often, leaky faucets are caused by an obstructed aerator, which is that little screen thing on the end of your faucet. Unscrew that, clean it with water and put it back on. If the faucet still leaks, there may be a loose fitting somewhere further down the line, in which case you may need to call in a plumber. (Bonus tip: To quiet the dripping noise until the leak is fixed, tie a length of string to the end of the faucet. The water will run down the string silently instead of clanging into the basin all night.)
  3. Garbage disposal won’t run
    The quickest and most common solution to this problem is the reset the garbage disposal by pressing the button on the unit under the sink.

If these tips don’t work to solve your kitchen plumbing conundrum, then it is probably best to call in a professional. Plumbing is a tricky thing – and garbage disposals can be dangerous – so sometimes it is best to leave it to the pros.

Tags: , , , ,
Posted in Plumbing, Plumbing Advice, Plumbing Maintenance, Yes! Plumbing | Comments Off

Signs that You Have Hard Water: A Tip from Blue Diamond

Monday, December 5th, 2011

Hard water is fairly common, especially in Blue Diamond. It is called hard water because of the minerals in it, such as calcium, iron and lime. Depending on how “hard” the water is, it’s usually perfectly healthy, but can cause some other problems throughout the home.

Hard water can negatively affect the durability of household appliances like dishwashers and washing machines, as well as pipes and fixtures throughout the home. How do you know if you have hard water? Here are some common signs and symptoms to be on the lookout for:

  1. A white, scaly, filmy residue left behind on plumbing fixtures. In particular, you may notice these on showerheads, on stainless fixtures like the basin of your kitchen sink, on your silverware or in the coffee pot.
  2. Clothes that are not getting as clean as they should in the laundry. This is because hard water is less effective at washing away dirt. Likewise, you may notice soap scum residue in your tub or shower.
  3. Little or no lather from shampoo or soap while showering.
  4. A reddish tinge to hair over time. This is due to iron in the water that can temporarily change hair color in the shower.
  5. Water takes a long time to heat, or heating costs that are higher than usual. This is because hard water requires more heat than water with fewer minerals in it.
  6. A foul odor emanating from your water.

If you notice any of these signs, or a combination of them, you may have hard water. There are certain things you can do to control the effects of hard water, such as using a commercial mineral remover to dissolve deposits left on showerheads and other fixtures. Vinegar also works well.

However, the best thing to do is to treat hard water so that it does not damage your plumbing system. A licensed plumber can help you do this by adding a water filtration system, among other treatments. These are things that need to be done on an ongoing basis, but will help extend the life of your expensive appliances and plumbing system.

Tags: , , ,
Posted in Plumbing | Comments Off

Plumbing Basics: Some Pointers from Henderson

Monday, November 7th, 2011

There are a lot of pipes, drains, fixtures and appliances in your Henderson home carrying out some pretty incredible tasks. For most people, plumbing is just another system that makes their lives easier. But, if something goes wrong, it’s important that you know exactly what to do and for that, you need to know how your system works.

Fundamental Plumbing

Plumbing is based entirely on the properties of gravity and water pressure. A plumbing system has two basic systems – one that brings water in and one that removes that water once you’ve used it. To bring water into your home, it is pressurized. With enough pressure, it can travel against gravity, rising in the pipes to your fixtures.

Every fixture in your home has a valve on it that allows you to shut off the flow of water when making repairs or if there is an emergency. If the emergency is big enough, you can turn the main water supply valve off outside your home as well.

Drainage Systems

While the water coming into your home is relatively simple – pressurized cold water goes directly to the fixtures and hot water comes from your hot water heater – the drainage system is slightly more complicated.

Once water has exited the faucets in your fixtures, it is no longer pressurized so gravity is needed to remove it. Each drain consists of a few basic parts – the flange, tail piece, trap, and drain extension. When you put water down a drain it goes into the trap and flows into the drain extension, eventually to the sewer line.

The trap is designed to always hold a small amount of water so that sewer gasses cannot back up into your fixtures. Vents are installed in your home as well to ensure there is always air in the plumbing system. That air ensures a vacuum doesn’t generate. If it did, water couldn’t flow out of the house. It’s the same as pouring from a small hole in a can – if you poke a hole in the opposite side, it flows much faster because air enters the can to displace the liquid.

Fixing Your Problems

A plumbing system is surprisingly simple to work on if you understand the basics. But, that doesn’t mean a professional isn’t needed for most major jobs. Because a single fixture or pipe can have an impact on the entire system and because water leakage can be incredibly damaging, it is best to call a professional whenever you need a second opinion or are unsure you can handle it on your own.

Tags: , , , , ,
Posted in Plumbing | Comments Off

Why Do I Need Water Filtration? A Question from North Las Vegas

Monday, October 24th, 2011

Like most North Las Vegas homeowners, you’re probably asking yourself why you need water filtration – what exactly happens to your water that makes it necessary to install an entire new system in your home to keep it clean? There are a few things that might be an issue here and your specific circumstances will determine which affects you the most.

Common Water Contaminants

While most homes don’t suffer from all of the following, there is a good chance you will have at least some of these contaminants in your home:

  • Sediment
  • Bacteria
  • Chlorine
  • Copper
  • Fluoride
  • Iron
  • Manganese
  • Nitrate
  • Sulfate
  • Viruses

This is only a partial list too – there are a number of other, more exotic substances that might be in your water. Now, this doesn’t mean your water suffers from all or even most of these problems. Many homes only have one or two contaminants and they may not even be immediately dangerous to your health.

But, here’s the issue – and the number one reason that most homes should have a water filtration system. Things change. While your home may not suffer from virus or sulfate infiltration now, it could later. Things happen to the water supply – pipes get old, things get into the water tables and chemical levels change at treatment plants.

The only way to combat these problems is to have a good water filtration system already in place. Specifically, a reverse osmosis system that can remove all of these contaminants through an advanced chemical process.

Testing Comes First

To make sure you have the right system in place to tackle your water contamination problems, make sure you first contact someone to perform full water testing on your home’s drinking water. Because some of these contaminants must be treated with chemical infusions through pumps or special cartridges, it is important to know in advance what you’re up against.

Tags: , , ,
Posted in Plumbing | Comments Off

Save Money with Your Water Heater in Las Vegas

Wednesday, October 19th, 2011

Did you know that water heating is one of the biggest energy expenses in your Las Vegas home? And the good news is that it is not too difficult to cut down on your water heating bills.

One thing you can do is install low-flow faucets and showerheads that use less water. The less water your use, the less water you need to heat, and the more energy you save. Since this upgrade will save money on both your water and energy bills, you will quickly make up any initial installation expense.

Another easy trick is to lower the temperature of your water heater. Check your settings; you really do not need to have your water heater thermostat set higher than 120 degrees. That temperature will still provide you with water hot enough to perform your daily tasks, but not waste energy by heating your water too much.

You can also upgrade your appliances, like your dishwasher and your clothes washer, to ones that are Energy Star rated. These will save you both water and energy every week. If you are looking for a bigger upgrade, get a new water heater. There are lots of energy-efficient and tankless models on the market today that will be a distinct improvement on water heaters made even as recently as seven years ago. If you replace these three major appliances your water heating bills will be significantly reduced.

For more information about installing a new water heater, talk to your local contractor.

Tags: , , , , ,
Posted in Energy Savings | Comments Off

How to Get Lime Out of Your Pipes (and Your Teapot): A Tip From Summerlin

Monday, October 10th, 2011

Lime deposits are what cause that white, chalky, filmy residue that you see on faucets, shower heads and tiles in your Summerlin home. Aside from being unsightly, lime deposits can also cause damage over time. Lime builds up inside the plumbing of your home, slowly degrading your pipes. Below are some tips to get rid of lime in common trouble spots.

Pipes

Lime most often builds up in pipes that carry hot water, since the water heater dissolves the lime in the water. The lime is then deposited on the inside of the pipes when it cools. Here are some steps to clear out the troublesome lime from those pipes:

  1. Turn off your water heater and drain it so it is about half full.
  2. Remove the pressure valve, being careful to follow the manufacturer’s instructions.
  3. Pour solvent into the heater through the open valve. There are commercial products available specifically designed to break up lime deposits, but white vinegar can be used as a cheaper and greener alternative.
  4. Replace the pressure valve, turn the heater back on and allow it to fill all the way.
  5. Turn on hot water faucets throughout the house. Let the water run until it runs clear or doesn’t smell of vinegar, depending on which solvent you used.

Kettles & Coffeemakers

Mineral deposits in a kettle or coffeemaker can cause your morning beverages to taste bitter. To clean them out, try these techniques:

  • Put 2 tablespoons of water softener in your kettle and fill it with water. Bring to a boil and rinse thoroughly. Alternatively, you can use a 1:1 ratio of vinegar and water, then let it sit overnight after boiling.
  • Fill your coffeemaker’s reservoir with water plus 2 tablespoons of water softener. Or, fill it entirely with white vinegar. Either way, run it through once that way, then a few more times with pure water to rinse.

For more obvious deposits, like faucets and tiles, usually a combination of hot water and either lime remover or white vinegar will do the trick. You can get more instruction on removing lime scale at HowToCleanStuff.net.

Those are the tried-and-true methods for making your pipes last by keeping lime at bay. Some plumbers will swear to you that putting magnets on your pipes will prevent lime from building up. Data to support that is inconclusive at best, although it can’t hurt to try. If you have more questions, contact your local plumber.

Tags: , , ,
Posted in Plumbing | Comments Off

Water and Energy Saving Tips From Henderson

Friday, October 7th, 2011

The cost of the heat, air conditioning and water supply to your Henderson home can be a lot and most people want to reduce their monthly bills.  But, how can you do that without cutting into the creature comforts and conveniences you’ve gotten used to over the course of the last few decades? Here are a few simple energy and water saving tips to make your life easier.

  • Patching Leaks – Two of the biggest wasters of water are dripping faucets and leaky pipes. The amount of water wasted by a single drip every second could provide for multiple baths per year – it adds up fast. Not only are leaky faucets and pipes easy to fix; they tend to develop into bigger problems as time passes.
  • Drains and Flushing – If you put a piece of toilet paper in the toilet used to clean an eye or wipe the counter, don’t flush. It’s a waste of water. If you notice some extra toothpaste in the sink, don’t rinse yet. You can always use the water from brushing your teeth or washing your face to clean it out. Multi-task and minimize how much water goes down the drain to save water.
  • Fully Loaded – A partially filled washing machine or dish washer is a huge waster of water. Fill it up and wait to run the device until it’s at the brim – the same amount of water is used no matter how much is in the device.
  • Lower Water Flow – Don’t crank your faucets up to the max just to get a glass of water or to check for hot water. It’s a waste of energy and it’s often unnecessary, especially when waiting for water to hit the right temperature.

If you’re interested in getting the most out of your home’s water supply, there are hundreds of little ways to save water that will add up over time. These are just some of the easiest ways to get started. If are interested in upgrading your current plumbing, contact your local contractor.

Tags: , , , , ,
Posted in Plumbing | Comments Off

Is There REALLY Such a Thing as Plumbing Maintenance? A Question From Boulder City

Friday, September 16th, 2011

Because it is so specialized and can lead to big messes if handled improperly, your Boulder City home’s plumbing is sometimes neglected among routine areas of maintenance. This is a mistake, however, as there are some routine tasks that should be performed on plumbing systems, such as:

  • Remove rust, calcium and lime deposits from the water heater
  • Cleaning the aerators
  • Clearing drain lines
  • Sharpening disposal blades

Some of these are simpler than others, but for the most part, unless you are a very savvy homeowner, they should be done by a licensed plumber. Even if you are not up to doing your own plumbing work, there are still plenty of routine things you can do in order to detect potential problems and see if further work is needed.

In the Bathroom

  • Unscrew the showerhead and look for deposits of lime, calcium, rust and other minerals.
  • Run water down shower and tub drains for signs of slow drainage.
  • Inspect the shower/tub for cracked tiles, which can be signs of leakage beneath the surface.
  • Flush each toilet with the tank lid off to make sure they are flushing properly and all parts are working.
  • Examine all caulking for cracks, gaps or peeling.

In the Kitchen

  • Turn on the faucets. See if water leaks out of the knobs, handles or elsewhere.
  • Have leaky faucets fixed right away.
  • Look beneath the sink for signs of leakage from the exposed drain pipes.

Elsewhere around the House

  • Take a look at the flame and burner chamber of your water heater. A yellowed flame may mean the fuel jets need to be cleaned. Make sure the chamber is free of rust and other small debris.
  • Inspect the washing machines hoses for loose joints, cracking or holes.
  • Look for mold and mildew throughout.

Next Steps

If you find any troublesome issues during this inspection, it is time to call in a professional to get them fixed right away. Doing this simple walkthrough once to twice a year can help prevent plumbing disasters before they happen.

Tags: , , , ,
Posted in Plumbing | Comments Off

Troubleshooting Drain Problems: A Guide From Henderson

Wednesday, September 14th, 2011

It’s Saturday afternoon and you are preparing dinner for a number of guests in your Henderson home. The kitchen is packed with groceries and you start to clean a lot of veggies for dipping. But there is a problem. The drain in your kitchen sink is “acting funny.” It drains slowly and is making a gurgling sound. In fact, it’s beginning to smelly funny, too.

The timing couldn’t be worse. Before you hit the panic button, let’s take a moment to troubleshoot the problem. Maybe it isn’t much of a problem after all.

First of all, is the problem confined to just the kitchen sink? There may be similar problems in other sinks, which would indicate a larger problem with the plumbing in your home. Hopefully, the kitchen sink is the only area you need to be concerned with.

Next, if you have a two-basin sink who should check to see if both sides are clogged or just one. Remove all dishes and utensils and run water on both sides. If water drains from one and not the other, there is a clog somewhere in the pipe leading to the union of both pipes. You have now centralized the drain problem. If both sides back up, the clog is further down the pipe. But it is still not a big problem.

One way to troubleshoot for drain problems is to simply run very hot water down the drain. This tends to break up clogs of grease by melting it away. The fix can also be as simple as running the garbage disposal long enough to dislodge any debris. You may even want to grind up some food you were planning to dispose of or take some lettuce greens and use the disposal on them. If this food takes a long time to grind or doesn’t at all, the disposal may be the culprit, leading to blocked drains.

And if you are preparing for your party by taking a shower and the shower drain is acting funny, don’t hit the panic button just yet. You may just have a build-up of hair or skin on the drain cover or screen. Use you foot to swish around the water and if water drains more quickly when you do this, the fix can be as simple as reaching down and picking up the debris. Having a plunger nearby helps, too.

None of this is brain surgery and quick fixes are easy to do. But if the problem persists and you don’t have the time or patience to work on your drain problem, call a plumbing professional – and stick with your party plans.

Tags: , , ,
Posted in Plumbing | Comments Off

« Older Entries