Posts Tagged ‘DIY’

Spring Valley Plumber’s Tip: How to Replace a Bathroom Faucet

Wednesday, December 21st, 2011

Whether your old faucet is broken or you just want to spruce up the bathroom a bit, installing a new faucet in your Spring Valley home is a relatively cheap and easy solution. It is one plumbing project that can be done via the DIY route, it takes only a few hours to do and it does not cost much.

Before you get started, make sure you have chosen the right type of faucet as a replacement. There are a few different kinds and you will want to replace the old sink with a similar kind in order to prevent problems and headaches during and after installation. If you’re unsure what kind you need, either consult the manual, take a picture to bring with you to the store or have a plumber take a look at it.

Once you have the right faucet picked out, it’s time to get to work:

  1. As always, turn off the water supply. There should be shutoff valves for the hot and cold water supplies right underneath the sink to make it easy on you.
  2. Unscrew the drain collar from the drain rim. Making sure everything is clean, place the house in the center of the middle hole. Screw it in place with the mounting nut. Tighten it up with a basin wrench, but take care not to over tighten. This can crack the porcelain.
  3. To install the hot and cold valves, begin by loosening the mounting nut on one and removing it. Replace it with the corresponding new valve. Repeat on the other side.
  4. Screw the braided lines to the valves you just installed, as well as to the spout. Tighten with a wrench, but again take care not to over tighten.
  5. Secure the faucet handles onto the valves that you installed in step #3. Make sure to put each handle on the correct valve.
  6. Fit the supply lines. You may have to do some cutting if you are using rigid supply lines rather than braided ones.
  7. Assemble and connect the pop-up drain assembly. You may have to test and adjust it a few times in order to get the right fit when open and closed. Secure the rods in place.
  8. Turn the water back on and check for leaks. Turn on the faucet for a bit to flush out the system before using.

Your sparkling new faucet is all set! If you have any problems, don’t hesitate to call your local plumber.

Tags: , , , , ,
Posted in Plumbing | Comments Off

Las Vegas Plumber’s Guide: How to Stop a Toilet from Overflowing

Monday, December 19th, 2011

An overflowing toilet is a really unpleasant problem to have in your Las Vegas home, and one you will undoubtedly want to correct right away. Toilets are reliable in that they tend to last a long time and not act up much, but when yours does start to malfunction, you pay attention right away.

To start with, examine the root cause of the overflow problem. There are three major causes of overflow: a clogged or blocked drain that does not allow the toilet to flush properly, an improperly adjusted float that allows the tank to overfill and a blocked vent pipe that replaces the air in the pipe after each flush.

Each of these requires a different course of action, so let’s discuss each individually.

If the drain is blocked, you will probably know right away. For one, water will overflow from the toilet’s bowl rather than the tank. For another, there will probably be quite a mess. Treating this type of overflow problem is straightforward—remove the clog. For simple clogs, a plunger and some elbow grease will get it done. Another trick is to stick the open mouth of an empty two liter bottle into the drain and squeeze. The blast of air can knock the clog free.

If your toilet is clogging and overflowing frequently, however, the problem may not be with the drain or with anything you are doing. It may be that the vent pipe is clogged. A vent pipe moves external into the plumbing system to replace the air that is pumped out with each flush. When it is blocked, the toilet can’t flush properly, which can lead to overflowing. If you have trouble with frequent clogging, call a plumber to inspect the situation.

In both of those situations, the toilet bowl will overflow. Another possibility is that the tank overflows, which is a different kind of problem. This is often cause by the filler float being set too high, so the tank fills with too much water. You can fix this by simply adjusting the mechanism inside the tank that controls the level of the float.

Whether it’s one of these three, or something else entirely, when your toilet overflows, be sure to check it out and get it fixed right away. And if you can’t fix it yourself, call your Las Vegas plumber.

Tags: , , , , , ,
Posted in Plumbing | Comments Off

Summerlin Plumbing Guide: How to Change a Drain Trap

Monday, December 12th, 2011

Have you ever noticed that U-shaped length of pipe below your Summerlin home’s bathroom or kitchen sink? Does it ever seem to you like it doesn’t make sense to have that in there? It seems counterintuitive to have the water run any direction other than straight down.

Well, that little bend is the drain trap, and it keeps nasty odors and gases from wafting their way up through the plumbing and into your home. The U shape of the trap precludes the normal upward drift of the gases, so they don’t make it up through your drain.

After a while, these traps can become corroded, choked with debris or entirely clogged to such a degree that it needs to be replaced. When this happens, it is important to take care of this right away.

As with any plumbing project, the first step is to turn off the main water supply. Don’t worry about the inconvenience; the whole process will take less than an hour.

Next, remove all the pieces of the existing drain trap. Use a pipe wrench and/or slip-joint pliers to remove the nuts and pull the trap free. Attach a tailpiece washer to your new tailpiece, and then attach the tailpiece to the sink strainer. You may need to cut the tailpiece to length with a hacksaw.

With a slip nut and washer, affix the trap arm to the drain stub. Again, you may need to cut the trap arm to length.

Finally, attach the trap bend to the trap arm, making sure the beveled face of the washer faces the trap bend. Tighten all the nuts and turn the water back on. Run a little water down the drain and check for leaks before using it. You may need to tighten some joints or apply Teflon tape in some places.

Once everything is all sealed up, you’re good to go! Your new drain trap is in place and ready to use. And if you run into any problems, talk to your local contractor.

Tags: , , , , ,
Posted in Plumbing | Comments Off

How To Read a Water Meter: A Guide From Henderson

Friday, August 19th, 2011

It doesn’t take rocket science to read a water meter in Henderson. Or does it?

Do you know much about water meters and their main function? The answer is probably too obvious, the main function of a water meter is to meter the amount of water usage in a home or building. Not rocket science, unless…

Unless you don’t know where your water meter is, that is. In most cases, the water meter is located at the front of your property near the street – located there for easy reading by water department utility “meter readers.” The meter could also be located in a home’s basement, too.

To take a reading of your meter, locate the white numbers on the right side of the meter dial with the black background. These numbers count the number of gallons of water that have passed through your meter since it was installed or reset. Don’t be surprised to find a lot of numbers, particularly in an older home. The American Water Works Association estimates that the daily use of water per capita is 69.3 gallons. Multiply that by several years and the numbers become very big.

If you want to take a sampling of your daily usage, do the following:

  • Select a day to take the initial reading.
  • Write down the numbers on the meter odometer.
  • The next day (or week or month) at the exact same time on the 24-hour clock you took the initial reading, write down the new odometer reading.
  • Subtract the initial reading from the new reading and you get the consumption for that sampling time period. When you water bill comes from the city, you may want to “compare notes” to see if your billing is accurate.
  • Remember that events like overnight guests, filling a pool or hot tub, or excessive showering will impact the readings.

If you take the time to understand the numbers, it may also help you decide on ways to conserve water. It may also provide a hint to any possible water leaks in your home from sources like a toilet valve or garden hose. A meter reading can lead to a plumbing repair job.

Reading a water meter may not require rocket science mentality but understanding the numbers could be very beneficial to your wallet and your well-being.

Tags: , , , , ,
Posted in Plumbing | Comments Off